 |
Camsorb® Riga-Sorb
Glide/Pack®
Medium-capacity odor and contaminant
control in a low pressure drop side access housing.The
Camsorb® RS Glide/Pack® can
be used for commercial applications, industrial applications,
manufacturing facilities, medical facilities or any other
applications where the control of gaseous contaminants
may be a concern.
It may also be used to reduce ventilation air through recirculation,
thus saving energy during the heating and cooling seasons. The Camsorb RS Glide/Pack is an excellent choice for ventilation
air correction in areas of non-attainment per ASHRAE Standard
62.Each unit provides side-access housing convenience, for
interior or exterior installation, where the housing mates
to other housings or a ducted HVAC system.
|
 |
Camsorb® Retainer/Pack
Medium-capacity odor and dust
control in a low pressure drop built-up bank system.
The Camsorb® RS80
Retainer/Pack can be used in commercial applications,
industrial applications,
manufacturing facilities, medical facilities or any other
applications where the control of gaseous contaminants
may be a concern.
It may also be used to reduce ventilation air through recirculation,
thus saving energy during the heating and cooling seasons. The Camsorb RS80 Retainer/Pack is an excellent choice for
ventilation air improvement in areas of air quality non-attainment
per ASHRAE Standard 62. Each adsorber module is a single
unit that may be stacked up to four units high, and any number
of units wide, to form a complete filter bank. Each module
may include 48 pounds of adsorbent, a prefilter or dusting
filter and a high efficiency particulate filter.
|
 |
Camsorb® RS
80 Two-Inch Panel
2-inch panel for removal of
odors or cleaning of make-up air at medium loads. Camfil
Farr Camsorb® RS
80 two-inch panels can be used to control odors or limit
VOC exposure created
by contaminants in the typical office environment. They may also be used in areas of non-attainment to clean
make-up air before it is introduced to the indoor environment. |
 |
Riga-Sorb 25D
A 2-inch bypass panel for control of low level to intermittent
odors and low-level ozone removal in non-EPA compliant areas.
Camfil Farr Camsorb RS25D panels can be used to control
low-level or intermittent odors, and/or reduce ozone levels
in geographic areas of EPA non-compliance. |
 |
3CF
Glide/Pack®
High-capacity gaseous contaminant and odor control in a side-
access filter housing. The Camfil Farr Camsorb two-stage side-access
sorbent panel housing can be used in commercial applications,
industrial applications, manufacturing facilities, medical
facilities or any other applications where the control of odors
and gaseous contaminants are a concern.
The housing
can also be used to reduce make-up air by increasing recirculated
air, thus
reducing energy costs during the heating
and cooling seasons. The Camsorb 3CF Glide/Pack® housing
provides side-access convenience for interior or exterior
installation. It is designed to mate to other housings or
installed in a ducted HVAC system.
|
 |
CF4A
High-capacity gaseous contaminant and odor control in a modular,
built-up bank assembly. The Camfil Farr built-up bank sorbent
panel assembly can be used in commercial applications, industrial
applications, manufacturing facilities, medical facilities
or any other applications where the control of gaseous contaminants
or odors may be a concern. It may also be used to reduce outside
air by increasing recirculated air, thus saving energy during
the heating and cooling seasons.
Each Camfil Farr built-up bank adsorber module assembles
into a built-up bank of gaseous and particulate filtration
with 85 pounds of adsorbent per 2000 cfm, a prefilter (of
any depth) and a final filter (of any depth).
|
 |
Camsorb® CF
One-Inch Panels
High-capacity loose-fill plastic
panels for gaseous contaminant & odor
removal. The industry standard for practical odor control,
Camfil Farr 1-inch polystyrene panels (formerly known as Farr
CF panels) were the first high-velocity ‘straight through’ carbon
purification filters available. Recommended for high gas/vapor load make-up air and recirculation
applications, where high removal efficiency and a large quantity
of sorbent media is required.
|
 |
Camsorb® Pleated
V-Cell Cartridge The Camsorb® Pleated
V-Cell Cartridge Filter is designed to fit in place of existing
12" deep filters within an air-handler. Use of the Camsorb
Pleated V-Cell Particulate + Carbon Cartridge Filter for
dust, pollution and odor control.
The filter also allows make-up air intake flow to be lowered,
thereby significantly reducing operating costs associated
with the energy purchased for heating and cooling that make-up
air. This method for contaminant removal is specifically
prescribed in ASHRAE Standard 62 - Ventilation for Acceptable
Indoor Air Quality.
|
 |
Campure™ GDM
440
Camfil Farr’s Campure™ GDM
440 Adsorber Modules incorporate Campure Molecular Filtration
Media in an easy-to-service disposable plastic module.
Designed to remove corrosive gases
from make-up air streams in commercial/industrial environments.
Exact replacement
for existing commercial & industrial make-up air systems.
|
 |
Campure™ GDM
300
Camfil Farr’s Campure™ GDM
300 Adsorber Modules incorporate Campure Molecular Filtration
Media in an easy-to-service disposable plastic module.
Designed to remove corrosive gases from exhaust streams
in industrial environments. Exact replacement for existing
industrial exhaust systems.
|
 |
Camsorb® CH
Loose-Fill V-Cell Cartridge
The Camsorb® CH Loose-Fill V-Cell
Cartridge is recommended for reduction of modest occupancy
odor loads, peak-shaving* of ambient air pollutants, and
continuous control of low-level gaseous contaminants in make-up
and air recirculation applications. It is a cost effective
filter for control of odors and outdoor pollution.
The Camsorb CH Loose-Fill V-Cell Cartridge may be installed
in any HVAC application where the use of outside air for
contaminant dilution is burdensome and cost-prohibitive to
the building operator. Use of the Camsorb CH Loose-Fill V-Cell
cartridge for contaminant adsorption and removal allows for
minimal introduction and conditioning of outside air, thereby
significantly reducing energy costs associated with heating
and cooling of required make-up air where a sorbent filter
is not applied. This method for contaminant removal is specifically
prescribed in the ASHRAE Standard 62, Ventilation for Acceptable
Indoor Air Quality.
|
 |
Camsorb® Canister
Holding Frames
Combines high-capacity sorbent canisters
with built-up bank frames for large system gaseous contaminant
control. Camfil Farr built-up bank holding frames for cylindrical
sorbent canisters are recommended for high gas/vapor load
make-up air and recirculation applications. A sorbent media
capacity, of up to 96 pounds per 2000 cfm, provides a higher
removal efficiency than other sorbent systems. This higher
media volume also ensures a higher contaminant loading capacity
than standard HVAC adsorption systems.
Frames are ideal for large system retrofits, custom air
handling systems and other HVAC systems handling large volumes
of air. When properly installed, the combination of Camsorb
holding frames and Camsorb sorbent canisters ensure that
virtually all of the air flowing through the system will
be efficiently treated by the filters.
|
 |
Camsorb® Canisters
Camfil Farr Camsorb® cylindrical
sorbent systems are recommended for high gas/vapor load make-up
air and recirculation applications, where high removal efficiency
and a large quantity of sorbent media are required. Applications
include: |
 |
Camsorb® Bag
Filter
Low pressure drop particulate filtration
combined with odor control. The City-Flo bag filter is a
totally new combination dust and odor control filter designed
for urban environments.
Ideal for office buildings, retail stores, shopping centers,
schools and other public buildings, located in close proximity
to heavily trafficked streets and roads.
|
 |
Campure™ Media
A comprehensive range of molecular filtration
medias for the control of corrosive gases, toxic gases, odors
and other gaseous pollutants. The medias may be used as part
of original equipment packages or as replacement for spent
media. The Campure™ range comprises chemically impregnated
adsorbents based on activated alumina which may be used on
their own or blended with activated carbon.
|
| |
|